Bests & Worsts Reviews from Amazon

I'm coming up (or just passed) about the three year mark using one of my EC155 machines (one is used much more than the other) and I can say that I've just about reached the end of the machine's lifetime. For the first two years of use, I pulled 18g shots two to three times a day and this past year has been an average of one pull a day in the morning (16g of coffee). If I compare the performance of the machine I use much more often and the machine that has about half a year's worth of use on it, I can definitely say that my three years of heavy use have just about knocked my EC155 out of its full capacity. The power of the pumps in the two machines have a night and day difference - I have to be very careful with how much coffee I load in the portafilter in the machine I use more to make sure it can still push out anything. As a side note, I can still achieve proper crema and pour lattes in both. Seeing as it's time to replace the dying EC155 I've reached a crossroads that speaks to the quality the EC155 provides at its price point. A lot of the "higher-end" (~$100-$500 range) espresso machines have issues that are apparent in the EC155 such as unstable temperature control and poor steam generation. For a sub-$100 machine, the EC155 does a great job as long as you know a few important tricks! Here are a few I've picked up through refining my coffee rituals: 1. Toss aside the pressurizer that comes with the portafilter (the small black circular object that screws into the plate and the black plate). This pressurizer works via a spring loaded system that attempts to introduce artificial pressure into the grounds so that the water coming through the portafiler needs to achieve a certain pressure before coming out. I've found that if you load enough grounds in and tamp properly it isn't necessary at all for achieving a crema. In the end you should just have three pieces: the outside of the portafilter, the gasket, and the metal holder 2. Either take off the bottom half of the portafilter handle or cut off the plastic underneath the portafilter to get yourself a sort of bottomless portafilter system. You'll be able to watch your shots come out of the machine and I've found that a lot of coffee liquid gets stuck in this piece without there being any big benefit. Also this frees up some much needed room for a taller cup. 3. Put a book or something under the machine to have more clearance for a frothing cup. 4. My routine for preparing a latte is to preheat the machine for anywhere between 30 minutes to hours (I used to have a outlet timer that would automatically turn my machine on in the morning). The top of the machine should be hot to the touch by the time you're ready to go for it. There will be a few cycles of heating in this time (i.e. green light on/off/on). I first weigh out my coffee (I grind mine fresh but I have used pre-ground before and there is a bit of a difference) and fill the portafilter and tamp it down (I usually use 18 grams in the larger portafilter). You lock the portafilter in as much as you can - it won't be completely straight but you should feel the gasket get tighter as you turn it. In accordance with espresso theory of not leaving a shot for more than a short time out, I heat/froth my milk first before actually pulling my shot. Frothing the milk to proper latte consistency to be able to pour art was probably the most difficult thing for me to achieve. Any machine has a little bit of water come out of the frother once you turn the knob so its best to have a cup to just purge out some excess water before you froth your milk. Since the EC155 has an auto-frother (i.e. has those holes in the top of the frother), you don't need to pull the milk and listen to the clicking noise as if you had a "legitimate" machine. Simply stretch the milk a bit (introduce air to create micro bubbles - should increase volume of milk) before finding a sweet spot where the milk is able to whirl around from the frother's airstream. This should incorporate those bubbles into your milk to get that silky consistency. I learned from SeattleCoffeeGear to leave the steamer valve on all the way and turn the knob to the coffee pull setting (all the way to the right) to purge out one shots' worth of coffee from the reservoir (until the green light turns off) just so that the machine is forced to heat a fresh amount of water to try to get that ideal temperature. 20-28 seconds of a pull and a bit of milk swirling and pouring later and you have a latte! 5. I descaled my machine a few times which helped the performance out a lot back in around year 2 but it looks like at this point the machine is going to have to be retired :/. The EC155 is really a great machine (especially for someone in college/grad school who needs to justify the price). Theres a lot of little tricks you can pick up that give the machine all the more character. I'm not sure if I'll stick to getting another EC155 next, but for anyone who's shell shocked by the prices forums and websites list for their machines, the EC155 is that affordable alternative. Like any culinary activity, if you focus on the ingredients (fresh roasted coffee) and prepare appropriately (burr grinder to achieve a consistent grind), you leave more leeway for the machine to work well. FYI I would rate myself as a budding coffee enthusiast, buying fresh roasted beans (light to medium roast) and I use a burr grinder.